Although there is no so-called technical secret in the welding process, there are many welding techniques, methods and processes in the actual welding process that can make the welding process easier. These processes are called technical know-how. Welding technical know-how can save time, cost and labor, and even determine the success or failure, profit or loss of welding.
Most welding processes are mainly based on scientific research, and some welding processes are based on actual welding experience. This article introduces the synthesis of welding experience in practice.
1. Welding process problems and solutions
1.1 Welding of thick and thin plates
1. When welding steel workpieces with gas shielded arc welding (GMAW) and flux-cored arc welding (FCAW), if the plate thickness of the workpiece exceeds the maximum welding current that the welder can reach, how to deal with it?
The solution is to preheat the metal before welding. Use propane, standard gas or acetylene welding torch to preheat the welding area of the workpiece at a preheating temperature of 150℃~260℃, and then weld. The purpose of preheating the metal in the welding area is to prevent the weld area from cooling too quickly, so as to prevent cracks or unfused welds.
2. If a thin metal cover is welded to a thicker steel pipe by using gas shielded arc welding or flux-cored arc welding, if the welding current cannot be adjusted correctly during welding, two situations may occur: one is to reduce the welding current to prevent the thin metal from burning through, and the thin metal cover cannot be welded to the thick steel pipe at this time; the other is that the welding current is too large to burn through the thin metal cover. How should it be handled at this time?
There are mainly two solutions.
① Adjust the welding current to avoid burning through the thin metal cover, and preheat the thick steel pipe with a welding torch, and then weld the two metal structures using a thin plate welding process.
② Adjust the welding current to be suitable for the welding of thick steel pipes. When welding, keep the welding arc on the thick steel pipe for 90% of the time, and reduce the time on the thin metal cover. It should be pointed out that only when this technology is mastered can a good welded joint be obtained.
3. When welding a thin-walled round tube or a rectangular thin-walled pipe fitting to a thick plate, the welding rod tends to burn through the thin-walled tube part. In addition to the above two solutions, are there any other solutions?
Yes, mainly using a heat sink during the welding process. If a solid round bar is inserted into a thin-walled round tube, or a solid rectangular bar is inserted into a rectangular pipe fitting, the solid bar will take away the heat of the thin-walled workpiece and prevent burn-through.
Generally speaking, solid round bars or rectangular bars are tightly installed in most hollow tube or rectangular tube materials supplied. When welding, care should be taken to keep the weld away from the end of the tube, which is the weakest area most prone to burn-through. The schematic diagram of using a built-in heat sink to avoid burn-through is shown in Figure 1.
4. When a galvanized or chromium-containing material must be welded to another part, how should it be operated?
The best process method is to file or grind the area around the weld before welding, because galvanized or chromium-containing metal plates will not only contaminate and weaken the weld, but also release toxic gases during welding.
1.2 Welding of containers and frame structures
1. If a welding process (such as brazing) is used to seal a buoy or the end of a hollow structure, how to prevent hot air from entering the container and causing the container to burst during the final sealing of the weld?
First, drill a pressure relief hole with a diameter of 1.5 mm on the buoy to facilitate the circulation of hot air near the weld and the external air, then perform closed welding, and finally weld the sealed pressure relief hole. The schematic diagram of sealing and welding a buoy or a closed container is shown in Figure 2.
When welding a gas storage container structure, a pressure relief hole can also be used. It should be noted that welding in a closed container is very dangerous. Before welding, ensure that the inside of the container or pipe is clean and avoid the presence of flammable and explosive items or gases.
2. When it is necessary to use metal arc welding, flux-cored arc welding or tungsten arc welding to weld a screen, wire mesh or extended metal to a steel structure frame, the wire mesh is prone to burn-through and the weld is not fused during welding. How to deal with it?
① Place a non-metallic washer on the wire mesh or extended metal and clamp the washer, wire mesh and frame together. Chrome or galvanized washers are not allowed. Washers should be uncoated, see Figure 3 (a).
② Place a larger washer on the upper part of the washer to be welded as a heat sink. The upper washer should have a larger hole than the lower washer to avoid the upper washer being welded together. Then plug weld through the two holes of the washer, and the weld should be in the lower washer part. The operator can take some other methods to get enough heat and weld, and pay attention to prevent the surrounding screen or wire mesh from burning through, see Figure 3 (b) and (c).
③ Another method is to use a metal strip with holes, align the holes with the part to be welded, place a heat dissipation washer, and then plug weld, see Figure 3 (d).
1.3 Repair of welded components
1. In addition to using the commonly used nail opener, what other methods can be used to remove damaged or rusted screws?
Here are two main methods:
① If the installed screw will not be damaged when heated, the nut and its assembly can be heated with an oxy-acetylene torch until it is red hot, and then quickly quenched in water to facilitate the removal of the screw. Several heating and quenching cycles may be required in this process.
② If the screw slot, nut or tooth socket is damaged or lost, a nut can be placed on the upper part (or the remaining part) of the screw head, tighten the nut, and then use any welding method to fill the metal inside the nut and screw.
This will connect the nut and the remaining part of the screw, and then place a wrench or tooth pliers on the nut to quickly pull out the screw. This method is conducive to providing a new grip point and using heat to tighten the screw. The schematic diagram of removing the remaining part of the fixing screw by welding is shown in Figure 4.
2. If there is a worn crankshaft, what is the best way to repair and reinforce it by welding?
When repairing a worn crankshaft, you can use metal arc welding, flux-cored gas arc welding or tungsten arc welding. However, to obtain a satisfactory weld bead shape, you must pay attention to the following 4 requirements.
① Make the cladding weld bead parallel to the crankshaft axis.
② First clad a weld bead on the lower part of the crankshaft, then rotate the crankshaft 180° and clad the next weld bead, which can balance the welding stress and significantly eliminate welding thermal deformation. It should be noted that sequential cladding on the first weld bead will cause crankshaft warping. This cladding process is suitable for repairing and welding roller crankshafts.
③ The overlap of the deposited metal between the two welds must be 30% to 50% to ensure that the weld surface is smooth during machining after welding repair.
④ When manual arc welding and flux-cored gas shielded welding are used, the residual flux between the welds must be cleaned with a brush or cutting method.
In addition to the above crankshaft repair method, it is also possible to add a cladding weld bead at every 90° position of the crankshaft to further reduce welding deformation. In the repair of bronze or copper parts, adding brazing metal is more beneficial than cladding in eliminating stress and deformation. The schematic diagram of repairing a worn crankshaft by welding is shown in Figure 5.
3. If a steel bearing is stuck in the equipment and you do not want to scrap the equipment, how should you use welding to remove the bearing?
First, weld a weld on the inner surface of the bearing, and use the tensile force of the weld to reduce the bearing diameter. The heat of the welding process should make the bearing movable. If a pipe with a diameter of 10cm is covered with welds on the inner surface, the diameter of the steel pipe will shrink by 1.2mm. The schematic diagram of using welding to remove a stuck bearing is shown in Figure 6.
4. Cracks often occur in oil tanks or ship plate structures. How should they be prevented?
First, drill a small hole at the end of the crack to facilitate the dispersion of the stress at the end over a larger range, and then weld a series of multi-pass welds of varying lengths to increase the strength of the steel plate at the front end of the crack. The schematic diagram of preventing cracks from extending in steel plates is shown in Figure 7.
2. Welding of reinforcement plates
2.1 Positioning and thickening of reinforcement plates
1. Welding reinforcement plates are often welded to the surface of steel plates (substrates). The corner welds on the outer edges of the reinforcement plates easily cause the center of the reinforcement plates to lift up, leave the surface of the steel plates and produce angular deformation, as shown in Figure 8 (a). This phenomenon will increase the difficulty of machining and turning. How should this problem be solved?
The solution is to use plug welding or slot welding in the middle of the reinforcement plate to close the surface of the reinforcement plate to the surface of the substrate to eliminate deformation and facilitate machining. The schematic diagram of positioning the reinforcement plate using plug welding or slot welding is shown in Figure 8 (b).
2. Sometimes the substrate needs to be thickened in a small area of the substrate, but the thickened area cannot exceed the area of the entire substrate. How should this be solved?
A thick plate of metal is embedded in the part of the substrate that needs to be thickened, and then fixed by welding. The schematic diagram of embedding a thick plate on the substrate is shown in Figure 9. This can provide sufficient thickness for subsequent machining, boring or drilling, and can replace large-thickness parts or castings in the equipment.
3. What is the standard method for increasing the rigidity of a plate to carry a load?
The standard method for increasing the rigidity of a plate to carry a load is to weld a series of angle steels vertically on the plate and add angle steel reinforcement ribs to increase the rigidity of the plate, as shown in Figure 10.
2.2 Controlling noise and vibration
1. What technical measures can be used to reduce the noise and vibration of metal plates?
The noise problem, like the vibration problem, can also be solved by reducing the resonant frequency of the metal plate. The main methods used are as follows:
① Increase rigidity by folding, curling or groove reinforcement;
② Cut the plate into a series of small parts to enhance support;
③ Use surface spray coating;
④ Bond a layer of vibration-damping fiber material on the surface of the plate.
The four methods of increasing the resonant frequency to reduce noise are shown in Figure 11. For vibrations caused at relatively low frequencies, the method of increasing metal stiffness is usually used to reduce vibrations, as shown in Figure 12.
2. When a plate is to be welded to another plate in a vertical direction for a fillet weld, if there is only a C-shaped clamp now, how should it be done?
During welding, a steel stopper or a rectangular object is used as an auxiliary tool, and a C-shaped clamp and a rectangular stopper are used to clamp the fillet weld, as shown in Figure 13.





