Feb 25, 2025 Leave a message

Can you tell the difference between horizontal turning and vertical turning?

CNC lathe is one of the most widely used CNC machine tools. It is mainly used for machining symmetrical rotating parts, such as shaft parts, inner and outer cylindrical surfaces of disk parts, inner and outer conical surfaces of arbitrary taper angles, complex rotating inner and outer curved surfaces, and cylindrical and conical threads.


Even the most common turning contours have different processes. In the SINUMERIK CNC system, all these process options are covered in the three categories of "transverse turning", "longitudinal turning (also known as "reciprocating turning")" and "grooving cutting". Let's take a look at them together.

1. Transverse turning


Features of transverse turning:

• During transverse turning, the moving direction of the turning tool is parallel to the axis of rotation of the workpiece.

• If it is a spindle, the tool moves from right to left; if the machine tool is equipped with a sub-spindle, the tool moves from left to right.

• Transverse turning can be used to process outer circles and inner holes. However, when processing inner holes, a bottom hole must be pre-drilled first.

• In addition to machining the outer circle, end face machining is also possible.


2. Longitudinal turning, grooving and cutting


Features of longitudinal turning of the side and end face (also called "reciprocating cutting"):

When longitudinally turning the side of the workpiece, the feed direction of the longitudinal turning tool is perpendicular to the axis of rotation of the workpiece.

When longitudinally turning the end face of the workpiece, the feed direction of the longitudinal turning tool is parallel to the workpiece axis.

The longitudinal turning tool has three cutting edges, so that the material removal process in the radial and axial directions is as uninterrupted as possible.

The blade shape and tool body shape of the grooving tool and the longitudinal cutting tool are different.


Features of grooving of the side and end face:

•  When grooving, cutting is only performed in the transverse feed direction.

•  The machining process of grooving of the side is perpendicular to the axis of rotation.

•  The machining process of grooving of the end face is parallel to the axis of rotation.

•  The grooving tool can only withstand forces applied perpendicularly to the tool axis.

• Grooving is mainly used to machine grooves. Usually (but not always) the groove to be machined is the same width as the groove cutting tool.


Characteristics of the cut-off process:


• At the end of the machining process, the workpiece is cut off by the cut-off tool.


• The cut-off cycle consists of an "auxiliary cut-in" and an actual cut-off process. The auxiliary cut-in ensures better chip evacuation.


• Cut-off requires the tool to feed beyond the rotation center of the workpiece.


• It is usually necessary to reduce the spindle speed before cutting to better control the rotating part to be cut off.


3. Example of turning with SINUMERIK Operate


As shown in the following three pictures, it is impossible to complete the machining of this handle part using only one cutting process, because the tool will not be in place or will interfere when it reaches the position marked by the orange circle in the figure.


Grooving process:


Longitudinal turning process:


Transverse turning (or "reciprocating turning"):


Therefore, we need to combine transverse turning and longitudinal turning processes to obtain the simulation effect shown below.


Note: Grooving and reciprocating turning are optional functions on the 828D PPU240 system. Option number (extended technology function): 6FC5800-0AP58-0YB0.

4. Summary


Transverse turning: + Larger transverse feeds can be achieved, that is, larger chip cross-sections. + Higher feed rates can be achieved during roughing. + Perfect chip evacuation. - Not all contours can be processed with limited tools, and more tools may need to be replaced during processing.

Longitudinal turning: + Avoids empty cutting strokes. + Reduces tool changes. + High flexibility in application. - Due to tool restrictions, not all contours can be processed. - Chip evacuation is sometimes not ideal (chips may be stuck).

When to use which process?

Longitudinal turning is generally used for: For example, parts with deep grooves and structures with 90° corners, which can only be processed using this process.

Transverse turning is generally used for streamlined contour structures with arc transitions.


Send Inquiry

whatsapp

Phone

E-mail

Inquiry