Welding characteristics of austenitic stainless steel: Significant elastic and plastic stresses and strains occur during welding, yet cold cracking rarely happens. Welded joints do not exhibit quench-hardening zones or significant grain coarsening, resulting in high tensile strength for the weld seam.
Key issues in welding austenitic stainless steel: Significant welding deformation; susceptibility to hot cracking due to grain boundary characteristics and sensitivity to certain trace impurities (such as S and P).
Image
Image
Five Major Welding Issues and Mitigation Measures for Austenitic Stainless Steel
01
Formation of chromium carbides reduces the welded joint's resistance to intergranular corrosion.
Intergranular corrosion: According to the chromium-depletion theory, when the weld seam and heat-affected zone (HAZ) are heated within the sensitization temperature range of 450°C–850°C, chromium carbides precipitate at the grain boundaries. This creates chromium-depleted zones at the boundaries, rendering them unable to resist corrosion effectively.
(1) The following measures can be taken to mitigate intergranular corrosion in the weld seam and corrosion in the sensitization zone of the base metal:
a. Reduce the carbon content in both the base metal and the weld metal. Add stabilizing elements (such as Ti or Nb) to the base metal to preferentially form MC-type carbides, thereby preventing the formation of Cr₂₃C₆.
b. Create a dual-phase microstructure in the weld seam consisting of austenite and a small amount of ferrite. The presence of ferrite refines the grain structure and increases the total grain boundary area, thereby reducing the amount of chromium carbide precipitation per unit area of the grain boundary.
Chromium has higher solubility in ferrite, so Cr₂₃C₆ forms preferentially within the ferrite phase rather than depleting chromium at the austenite grain boundaries. Additionally, ferrite dispersed within the austenite matrix acts as a barrier, preventing corrosion from propagating into the material along the grain boundaries.
c. Control the residence time within the sensitization temperature range. Adjust the welding thermal cycle to minimize the time spent between 600°C and 1000°C; high-energy-density welding methods (such as plasma arc welding) can be selected for this purpose. Use lower welding heat input; purge the back of the weld with argon or use copper backing to increase the cooling rate of the welded joint; minimize the number of arc starts and stops to avoid repeated heating; and, for multi-pass welds, weld the surface that will be in contact with the corrosive medium last whenever possible.
d. Perform post-weld solution treatment or stabilizing annealing (850°C–900°C) followed by air cooling to ensure full carbide precipitation and accelerate chromium diffusion.
Image
(2) Knife-line attack (a form of localized corrosion) in welded joints; the following preventive measures can be taken:
Due to the high diffusivity of carbon, it segregates at grain boundaries during cooling, creating a supersaturated state, whereas Ti and Nb remain within the grains due to their low diffusivity. When the welded joint is reheated within the sensitization temperature range, the supersaturated carbon precipitates at the grain boundaries in the form of Cr₂₃C₆.
a. Reduce carbon content. For stainless steels containing stabilizing elements, the carbon content should not exceed 0.06%.
b. Employ appropriate welding procedures. Select lower welding heat input to reduce the residence time of the overheated zone at high temperatures, and take care to avoid "intermediate-temperature sensitization" during welding.
For double-sided welding, the weld bead in contact with the corrosive medium should be deposited last (this is the reason why internal welding is performed after external welding for large-diameter, thick-walled welded pipes). If this is not feasible, welding parameters and weld geometry should be adjusted to minimize sensitization heating of the overheated zone that will contact the corrosive medium.
c. Post-weld heat treatment. Perform solution treatment or stabilization treatment after welding.
Image
02
Stress Corrosion Cracking
The following measures can be adopted to prevent stress corrosion cracking:
a. Correct material selection and appropriate adjustment of weld composition. High-purity Cr-Ni austenitic stainless steels, high-silicon Cr-Ni austenitic stainless steels, ferritic-austenitic stainless steels, and high-chromium ferritic stainless steels exhibit good resistance to stress corrosion; weld metal with an austenite-ferrite duplex structure also offers good resistance.
b. Eliminate or reduce residual stress. Perform post-weld stress-relief heat treatment, and use mechanical methods such as polishing, shot peening, and peening (hammering) to reduce surface residual stress.
c. Rational structural design to avoid significant stress concentrations.
Image
03
Welding hot cracks (weld solidification cracks, heat-affected zone liquefaction cracks)
Hot cracking susceptibility depends primarily on the material's chemical composition, microstructure, and properties. Nickel (Ni) readily forms low-melting-point compounds or eutectics with impurities such as sulfur (S) and phosphorus (P); segregation of elements like boron (B) and silicon (Si) also promotes hot cracking.
Weld seams tend to form coarse columnar grain structures with strong directionality, which facilitates the segregation of harmful impurities and elements. This promotes the formation of continuous intergranular liquid films, thereby increasing susceptibility to hot cracking. Non-uniform heating during welding can generate significant tensile stresses, further promoting the formation of hot cracks.
Preventive measures:
a. Strictly control the content of harmful impurities such as S and P.
b. Adjust the weld metal microstructure. Welds with a duplex (two-phase) microstructure exhibit good crack resistance; the delta (δ) phase in the weld refines grains, eliminates the directionality of single-phase austenite, and reduces the segregation of harmful impurities at grain boundaries. Additionally, the δ phase can dissolve larger amounts of S and P and lower interfacial energy, thereby inhibiting the formation of intergranular liquid films.
c. Adjust the alloy composition of the weld metal. Appropriately increasing the content of Mn, C, and N in single-phase austenitic steel, and adding trace elements such as cerium (Ce), zirconium (Zr), or tantalum (Ta)-which refine the weld microstructure and purify grain boundaries-can reduce hot cracking susceptibility.
d. Process measures. Minimize overheating of the weld pool to prevent the formation of coarse columnar grains; employ low heat input (low linear energy) and small-cross-section weld beads.
For example, 25-20 type austenitic steels are prone to liquefaction cracking. Measures to mitigate this include strictly limiting impurity content and grain size in the base metal, using high-energy-density welding methods, employing low heat input, and increasing the cooling rate of the joint. Image
04
Embrittlement of Welded Joints
For heat-resistant steels, the ductility of welded joints must be ensured to prevent high-temperature embrittlement; for low-temperature steels, good low-temperature toughness is required to prevent brittle fracture of the welded joints at low temperatures.
Image
05
Significant Welding Deformation
Due to low thermal conductivity and a high coefficient of thermal expansion, welding deformation tends to be significant; fixtures can be used to prevent this. Selection of welding methods and materials for austenitic stainless steel:
Austenitic stainless steel can be welded using methods such as Tungsten Inert Gas (TIG) welding, Metal Inert Gas (MIG) welding, Plasma Arc Welding (PAW), and Submerged Arc Welding (SAW).
Austenitic stainless steel has a low melting point, low thermal conductivity, and high electrical resistivity; therefore, lower welding currents are used. Narrow weld seams and narrow weld beads should be employed to minimize high-temperature dwell time, prevent carbide precipitation, reduce weld shrinkage stress, and lower susceptibility to hot cracking.

The composition of welding consumables-particularly alloying elements like Cr and Ni-should be higher than that of the base metal. Welding consumables containing a small amount (4%–12%) of ferrite are used to ensure good crack resistance (against cold cracking, hot cracking, and stress corrosion cracking) in the weld seam.
When the presence of a ferrite phase in the weld seam is prohibited or impossible, welding consumables containing alloying elements such as Mo and Mn should be selected.
Levels of C, S, P, Si, and Nb in welding consumables should be kept as low as possible; while Nb can cause solidification cracking in fully austenitic weld seams, the presence of a small amount of ferrite in the weld seam can effectively prevent this.
Welding consumables containing Nb are typically selected for welded structures requiring post-weld stabilization or stress-relief treatment. Submerged arc welding is used for medium-thickness plates; the burn-off loss of Cr and Ni can be compensated for by the transfer of alloying elements from the flux and welding wire.
Due to deep penetration, care must be taken to prevent hot cracking in the center of the weld seam and to avoid reducing corrosion resistance in the heat-affected zone (HAZ). Attention should be paid to selecting thinner welding wires and lower heat input; the welding wire should have low Si, S, and P content.
The ferrite content in heat-resistant stainless steel weld seams should not exceed 5%. For austenitic stainless steels with Cr and Ni contents exceeding 20%, high-manganese (6%–8%) welding wire and basic or neutral flux should be used; this prevents silicon pickup in the weld and enhances crack resistance.
Fluxes specifically designed for austenitic stainless steel result in minimal silicon pickup and can transfer alloying elements into the weld to compensate for burn-off losses, thereby meeting requirements for weld properties and chemical composition.





