Nov 01, 2024 Leave a message

The difference between transverse turning and longitudinal turning

 

CNC lathe is one of the most widely used CNC machine tools. It is mainly used for machining symmetrical rotating parts, such as shaft parts, inner and outer cylindrical surfaces of disk parts, inner and outer conical surfaces of arbitrary taper angles, complex rotating inner and outer curved surfaces, and cylindrical and conical threads.

Even the most common turning contours have different processes. In the SINUMERIK CNC system, all these process options are covered in the three categories of "transverse turning", "longitudinal turning (also known as "reciprocating turning")" and "groove cutting". Let's take a look at them together.

1. Transverse turning

Features of transverse turning:

• During transverse turning, the moving direction of the turning tool is parallel to the axis of rotation of the workpiece. • If it is a main spindle, the tool moves from right to left; if the machine tool is equipped with a sub-spindle, the tool moves from left to right. • Transverse turning can be used to machine external circles and internal holes. However, when machining internal holes, a bottom hole must be pre-drilled first. • In addition to machining external circles, end face machining can also be performed.
2. Longitudinal turning, grooving and parting

Characteristics of longitudinal turning of the side and end faces (also called "reciprocating cutting"):• When longitudinally turning the side of the workpiece, the feed direction of the longitudinal turning tool is perpendicular to the axis of rotation of the workpiece. • When longitudinally turning the end face of the workpiece, the feed direction of the longitudinal turning tool is parallel to the workpiece axis. • The longitudinal turning tool has three cutting edges, so that the material removal process in the radial and axial directions is as uninterrupted as possible. (Because the rapid movement stroke is minimized)• The blade shape and tool body shape of the grooving tool and the longitudinal cutting tool are different.
Characteristics of grooving of the side and end faces:
• When grooving, cutting is only performed in the transverse feed direction. • The machining process of grooving of the side is perpendicular to the axis of rotation. • The machining process of grooving of the end face is parallel to the axis of rotation. • The grooving tool can only withstand forces applied perpendicularly to the tool axis. • The grooving process is mainly used to process grooves. Usually (but not always) the groove to be machined is the same width as the groove cutting tool.
Characteristics of the cut-off process:

• At the end of the machining process, the workpiece is cut off by the cut-off tool. • The cut-off cycle consists of an "auxiliary cut-in" and an actual cut-off process. The auxiliary cut-in ensures better chip removal. • Cut-off requires the tool to feed beyond the rotation center of the workpiece. • It is usually necessary to reduce the spindle speed before cutting to better control the rotating part to be cut off.
3. Example of turning with SINUMERIK Operate

As shown in the following three pictures, it is impossible to complete the machining of this handle part using only one cutting process, because the tool will not be in place or will interfere when it reaches the position marked by the orange circle in the figure.
Groove cutting process:
Longitudinal turning process:
Transverse turning (or "reciprocating turning"):
Therefore, we need to combine transverse turning and longitudinal turning processes to obtain the simulation effect shown below: Note: Groove turning and reciprocating turning are optional functions on the 828D PPU240 system. Option number (extended technology function): 6FC5800-0AP58-0YB0
4. Summary

Transverse turning: + Larger transverse feed, i.e. larger chip cross-section area, can be achieved + Higher feed rate can be achieved during roughing + Perfect chip evacuation effect - Not all contours can be processed by transverse turning with limited tools, and more tools may need to be replaced during processing
Longitudinal turning: + Avoids empty cutting strokes + Reduces tool change operations + High flexibility in application - Due to tool limitations, not all contours can be processed - Chip evacuation effect is sometimes not ideal (chips may be stuck)
When to use which process? Longitudinal turning is generally used for: For example, parts with deep grooves and structures with 90° corners, which can only be processed using this process. Transverse turning is generally used for streamlined contour structures with arc transitions.

 

 

Send Inquiry

whatsapp

skype

E-mail

Inquiry