Feb 04, 2024 Leave a message

Do You Know How To Judge And Deal With The Wear Of Cutting Blades?

 

In order to achieve better quality of cutting and the longest possible tool life, we need to check the blade after processing, summarize the causes of different forms of blade wear and find solutions, which is the basis for successful milling.

Flank wear 1

Rapid wear results in poor surface quality or out-of-tolerance surfaces.

reason
Cutting speed too high
Insufficient wear resistance
Feed fz is too low

solution
Reduce cutting speed (vc)
Choose materials with higher wear resistance
Increase feed (fz)

Flank wear 2

Excessive wear results in short tool life.

reason
vibration
chip recutting
Burrs form on parts
Poor surface quality
generate heat

solution
Increase feed (fz)
Use down milling
Effective chip removal using compressed air
Check recommended cutting parameters

Flank wear 3


Uneven wear leads to damage to sharp corners.

reason
Tool runout
vibration
Short tool life
Poor surface quality
loud noise
Radial force too high

solution
Reduce runout to less than 0.02mm
Check collets and jackets
Minimize tool protrusion
Use fewer teeth for cutting
Choose a larger tool diameter
For solid carbide end mills and interchangeable head mills, choose a geometry with a larger helix angle (gp≥45°)
Divide the axial depth of cut (ap) into multiple passes
Reduce feed (fz)
Reduce cutting speed (vc)
High speed machining requires shallow tool passes
Improved tool and workpiece clamping

crater wear


Excessive wear results in reduced cutting edge strength. Broken cutting edges lead to poor surface quality.

picture


reason
Diffusion wear due to excessive cutting temperature on the rake face

solution
Choose aluminum oxide coating material
Choose a positive rake angle insert geometry
Reduce speed to obtain lower temperatures, then reduce feed

plastic deformation

Plastic deformation, collapse or flank depression of the cutting edge results in poor chip control, poor surface quality and insert breakage.

picture


reason
Cutting temperature and pressure are too high

solution
Choose a material with higher wear resistance (harder)
Reduce cutting speed (vc)
Reduce feed (fz)

Breaking Blade 1


The portion of the cutting edge that is not involved in cutting is damaged by chip hammering. Damage to the front and supporting surfaces of the insert, resulting in poor surface texture and excessive flank wear.


picture


reason
Chips are squeezed by the cutting edge

solution
Choose a grade with higher toughness
Choose an insert with a stronger cutting edge
Increase cutting speedvc
Choose a positive rake geometry
Reduce feed at start of cut
Improve stability

Breaking Blade 2


A small portion of the cutting edge breaks (chips) resulting in poor surface quality and excessive flank wear.

picture


reason
Material toughness is too low
Insert geometry is too weak
built-up edge

solution
Choose a grade with higher toughness
Choose an insert with a stronger geometry
Increase the cutting speed vc, or choose a positive rake angle geometry
Reduce feed at start of cut

Groove wear


Groove wear leads to poor surface quality and risk of cutting edge breakage.

picture

reason
Work hardened materials
epidermis and oxide scale

solution
Reduce cutting speed (vc)
Choose a grade with higher toughness
Use a stronger geometry
Use a cutting angle closer to 45°
Use round blades to ensure best results
Delay wear and tear using variable ap technology

hot cracks

Small cracks perpendicular to the cutting edge due to temperature changes lead to chipping and poor surface quality.


picture


reason
Intermittent processing
Changing cutting fluid supply

solution
Choose materials with higher toughness and better thermal shock resistance
Cutting fluid should be used in sufficient quantities or not at all

Built-up edge 1

Built-up edge results in poor surface quality and causes the cutting edge to chip when it breaks off.


picture


reason
The temperature of the cutting area is too low
Materials with very high viscosity such as mild steel, stainless steel and aluminum

solution
Increase cutting speedvc
Change to a more suitable insert geometry

Built-up edge 2

The workpiece material is welded to the cutting edge.

picture


reason
low cutting speed vc
low feed fz
Negative rake angle cutting geometry
Poor surface quality

solution
Increase cutting speedvc
Increase feed fz
Choose a positive rake geometry
Use oil mist or cutting fluid

 

 

 

Send Inquiry

whatsapp

skype

E-mail

Inquiry