Sep 30, 2023 Leave a message

I’ve Passed On The Calculation Method Of Sheet Metal Bending And Unfolding To You, Please Relay It On.

 

When sheet metal is bent and flattened, one side of the material will be elongated and one side will be compressed. The factors affected include: material type, material thickness, material heat treatment and processing bending angle. picture

Expand the calculation principle:

1. During the bending process of the sheet, the outer layer is subject to tensile stress, and the inner layer is subject to compressive stress. There is a transition layer between tension and compression that is neither tensile nor compressive, which is called the neutral layer; the neutral layer is under bending during the bending process. The length remains the same as before bending, so the neutral layer is the basis for calculating the unfolded length of the bent piece.

2. The position of the neutral layer is related to the degree of deformation. When the bending radius is large and the bending angle is small, the degree of deformation is small, and the position of the neutral layer is close to the center of the sheet thickness; when the bending radius becomes smaller, the bending angle increases. When it is large, the degree of deformation increases, and the position of the neutral layer gradually moves to the inside of the bending center. The distance from the neutral layer to the inside of the sheet is represented by λ.

The basic formula for expansion calculation:

Expanded length = inside material + inside material + compensation amount

1) General bending: (R=0, θ=90°)

picture

L=A+B+K

1. When 0≤T≤0.3, K=0

2. For iron materials:

a. When 0.3≤T≤1.5, K=0.4T

b. When 1.5≤T≤2.5, K=0.35T

c. When T>2.5, K=0.3T

3. For other non-ferrous metal materials such as AL, CU:

When T<0.3, K=0.4T

Note: When R≤2.0, it is treated as R=0.

2) General bending (R≠0 θ=90°)

picture

L=A+B+K K value takes the arc length of the neutral layer

1. When T≤1.5 λ=0.5T

2. When T>1.5, λ=0.4T

3) General bending (R=0 θ≠90°)

picture

L=A+B+K'

1. K'=0 when T≤0.3

2. When T<0.3 K'=(u/90)*K

Note: K is the compensation amount when 90∘

4) General bending (R≠0 θ≠90°)

picture

L=A+B+K

1. When T≤1.5 λ=0.5T

2. When T>1.5, λ=0.4T

The K value takes the arc length of the neutral layer

Note: When R≤2.0, and when processing with a folding knife, it is calculated as R=0, and A and B are determined according to the length of the straight edge after zero chamfering.

5) Z fold 1 (straight edge difference)

picture

1. When H>5T, when molding is done in two steps, calculation is based on two 90° bends

2. When H≤5T, one-time molding, L=A+B+K

The K value is based on the parameters in the attachment.

6) Z fold 2 (hypotenuse step difference)

1. When H≤2T, it is calculated according to the straight-edge step difference method, that is: expansion length = total length before expansion + K

K=0.2

2. When H>2T, bend and unfold in two sections (R=0 θ≠90°).

7) Draw hole

The calculation principle of the hole size is the principle of constant volume, that is, the volume of the material remains unchanged before and after hole drilling; for general hole drilling, it is calculated according to the following formula, and the parameters in the formula are shown in the figure on the right (assume the pre-punching hole is X, and add the correction coefficient –0.1 ):

1. If the drilled hole is a threaded hole (drilled and then tapped), the value of S should be determined according to the following principles:

When T≦0.5, take S=100%T

When 0.5<T<0.8, take S=70%T

When T≧0.8, take S=65%T

Generally, the value of pre-punching holes for common tooth extractions is as shown in Appendix 1.

2. If the drawn holes are used for riveting, then take S=50%T, H=T+T'+0.4 (Note: T' is the thickness of the plate to be riveted with, and the gap between the drawn holes and the salad holes is single Side 0.10~0.15)

3. If the holes are not marked in the original drawing, the inner and outer diameter dimensions after the holes are guaranteed to be

4. When the calculated value of the pre-punched hole diameter is less than 1.0, always take 1.0

8) Fold and flatten

L= A+B-0.4T

1. When flattening, depending on the actual situation, consider whether to press the line before bending. The pressing line position is in the middle of the bending deformation zone;

2. Reverse folding and flattening are generally performed in two steps.

V fold 30°

Reflex and flatten

Therefore, when drawing the bend line in the unfolded drawing, it must be drawn according to the 30° bend line.

9) N discount

1. When the N-fold processing method is to fold and flatten the gasket, it is calculated as L=A+B+K, and the K value is determined according to the parameters in the attachment.

2. When N-fold is processed in other ways, please refer to "General Bending (R≠0 θ≠90°)" for the unfolding algorithm.

Remark:

a. Dimensional design value with marked tolerance: Take the middle value of the upper and lower limit dimensions as the design standard value.

b. For the expansion of square holes and external corners, the processing method of the corners shall refer to the "Product Expansion Processing Standard", and the straight wall part shall be bent and expanded at 90°.

Send Inquiry

whatsapp

skype

E-mail

Inquiry