Sep 09, 2023 Leave a message

Parts Do Not Rust Depends On It

 

What is anti-rust oil?
Rust often refers to the corrosion of ferrous metals in the air due to the electrochemical action caused by the participation of water and oxygen. The anti-rust oil mainly uses the anti-rust agent to form a protective film on the metal surface to isolate water and oxygen so as to prevent rust.
picture

Classification of common antirust oils for mechanical parts processing
1. Thin layer anti-rust oil
The oil film is thin and the dosage is small. It forms a thin anti-rust film on the surface of the workpiece, which does not affect the appearance of the product. It is easy to clean and has good anti-rust performance. It is suitable for anti-rust and storage anti-rust between parts in the automotive, hardware and electronic industries.
2. Replacement anti-rust oil
It has dehydration performance and is suitable for products that have not been completely dried after cleaning. It can replace the water and facilitate subsequent cleaning. It is often used to prevent rust between processes and to seal and prevent rust.
3. Hard film anti-rust oil
It has excellent anti-rust performance in humid and salt spray environments. It is generally suitable for marine transportation, ship hulls, automobile chassis, equipment and other harsh environments that require high anti-rust performance.
picture
4. Water-based antirust agent
Mixed with water, low cost, widely used for anti-rust between ferrous metal, alloy steel and non-ferrous metal products, and the anti-rust period is short.
About the choice of anti-rust oil

1. Choose according to the product material:
Different metal materials have different requirements for anti-rust oil, such as cast iron and copper, which have different requirements for anti-rust properties.
2. Choose according to the anti-rust cycle:
For short-term anti-rust, you can use anti-rust oil with a lower viscosity and a thinner oil film. For longer-term anti-rust, you need an anti-rust oil with a higher viscosity and a thicker oil film.
3. Choose according to product structure and usage:
For example, smaller products can be rust-proofed by immersion, and larger products with more complex structures can be rust-proofed by spraying or brushing. No matter which method is used, it should be ensured that an effective anti-rust layer is formed on each part. Anti-rust film to avoid local corrosion (in addition, workers should be careful to avoid direct contact with the metal surface with their hands. Human sweat contains chloride ions, lactic acid and other rust-causing substances, which can easily form fingerprint-like rust on the surface of the workpiece).
picture

4. Choose according to the subsequent processing technology and assembly requirements:
Such as the post-processing technology, storage environment, packaging conditions, and whether cleaning is required before assembly.
How to use anti-rust oil and precautions
1. Soaking method: The advantage is that it can form a uniform anti-rust film on the surface to ensure complete coverage of the product, and the cost is low. The disadvantage is that it is only suitable for small products, using low-viscosity anti-rust oil, and the soaking tank must have good drainage. system.
2. Spray method: It is suitable for large-scale and complex-structured products. A high-efficiency sprayer must be used. It is easy for the product to fail to completely form an anti-rust film. The working environment requires good ventilation performance during use.
3. Brushing method: This method is simple to use, but it must be ensured that every position of the workpiece is brushed, and the brush must be kept clean before use.
4. Flushing method: high efficiency, recycling, and cost saving, but the products in the tank need to be drained and replaced regularly to avoid excessive moisture and other substances from affecting the anti-rust effect.
picture
The above points are some basic knowledge about the selection and use of anti-rust oil. In the production process, it is still easy to use anti-rust oil and rust occurs. Common reasons are: too much moisture on the surface of the workpiece, and the workpiece is not completely covered. An anti-rust film is formed, and the anti-rust oil is not replaced after being used for a long time. A large amount of moisture, dust, etc. remains in the oil. The anti-rust film on the surface of the workpiece is not fully formed before being packaged. Water vapor condensation caused by the temperature difference in the package causes rust. More serious, the packaging material or quality does not meet the process requirements, etc.

Send Inquiry

whatsapp

skype

E-mail

Inquiry