Jan 03, 2022 Leave a message

Positioning And Clamping Have Only One Purpose: No Deformation


This is the generalization of people in the industry when summarizing fixture design, but things are far from simple. In the process of contacting various schemes, we found that there are always some positioning and clamping in the preliminary design that are not well resolved. The most innovative solutions will lose their practical significance. Only by understanding the basic knowledge of positioning and clamping can the integrity of fixture design and processing solutions be fundamentally guaranteed.


1. The basic principle of positioning from the side of the workpiece


When positioning from the side of the workpiece, the same as the support, the three-point principle is the most basic principle. This is the same as the principle of the support, called the 3-point principle, which is derived from the principle of "three points not on the same straight line determine a plane". Among the 4 points, 3 points can determine a surface, so a total of 4 surfaces can be determined, but no matter how they are positioned, it is quite difficult to make the 4th point in the same plane.


For example, when using 4 fixed-height locators, only 3 points somewhere can touch the workpiece, and there is a high possibility that the remaining 4th point does not touch the workpiece.


Therefore, when configuring the locator, it is generally based on 3 points, and the distance between these 3 points should be increased as much as possible.


In addition, when placing the positioner, it is necessary to confirm in advance the direction in which the machining load is applied. The direction of the machining load is the direction of travel of the tool holder/tool, and the positioning of a positioner at the end of the tool feed direction can directly affect the overall accuracy of the workpiece.


Generally, when positioning the blank surface of the workpiece, a bolt-type adjustable positioner is used, and when positioning the workpiece processing surface, a fixed type (the contact surface of the workpiece is ground) positioner is used.



Second, the basic principle of positioning from the workpiece hole


When using the holes processed in the previous process of the workpiece for positioning, it is necessary to use pins with tolerances for positioning. By matching the accuracy of the workpiece hole with the accuracy of the shape of the pin and combining them according to the tolerance, the positioning accuracy can meet the actual needs.


In addition, when pins are used for positioning, generally one uses a straight column pin and the other uses a rhombic pin, so that it will be more convenient to assemble and disassemble the workpiece, and it is rare for the workpiece and the pin to be stuck.


Of course, it is also possible to use straight pins for both pins by adjusting the fit tolerance. For more precise positioning, it is usually most effective to use a straight pin and a diamond pin.


When using a straight pin and a rhombus pin, usually the line connecting the arrangement direction of the diamond pin (where it contacts the workpiece) is 90° perpendicular to the line between the straight pin and the rhombus pin. Orientation (rotation direction of the workpiece).




1. Classification of clamps


According to the clamping direction, it is generally divided into the following categories:


Next, let's take a look at the characteristics of various clamps.


1. Clamp that is pressed from above


The clamp that clamps from above the workpiece has the least amount of deformation when clamping, and the workpiece is the most stable in processing, so in general, the first consideration is to clamp from above the workpiece. The most common type of clamp that is pressed from above the workpiece is a manual mechanical clamp. For example, the figure below is called a "loose leaf" clamp. The clamp composed of the pressure plate, stud bolt, jack and nut is called "loose leaf type" clamp.


In addition, according to the shape of the workpiece, different shapes of pressing plates can be selected to correspond to various workpieces of different shapes.


The relationship between the torque and the clamping force when the loose leaf clamp is clamped can be calculated from the driving force of the bolt.


Clamps for clamping from above the workpiece include the following similar clamps in addition to loose leaf clamps.


2. Clamp for clamping from the side


Originally, the clamping method of clamping the workpiece from above has the most stable accuracy and the least processing load on the workpiece. However, when the workpiece needs to be processed, or clamping from above the workpiece is not very suitable, etc., it is not possible to clamp from above the workpiece, you can choose to clamp from the side of the workpiece. However, relatively speaking, when the workpiece is clamped from the side, a floating force will be generated. How to eliminate this force must be paid attention to when designing the fixture.


Clamps that are clamped from the side are also shown in the figure above. While generating thrust from the side, there is an oblique downward force. This kind of clamp can effectively prevent the workpiece from floating up.


There are clamps similar to the following for clamping from the side.



3. The clamp that tightens the workpiece from below


When processing the upper surface of a thin-plate workpiece, it is not only impossible to clamp from above, but also unreasonable to press from the side. The only reasonable clamping method is to tighten the workpiece from below. When tightening the workpiece from below, if the workpiece is made of iron, a magnet-type clamp can usually be used. For non-ferrous metal workpieces, vacuum suction cups can generally be used to tighten them.


In the above two cases, the magnitude of the clamping force is proportional to the magnitude of the contact area between the workpiece and the magnet or vacuum chuck. If the processing load is too large when processing small workpieces, the processing effect will not be ideal.


picture


In addition, when using magnets or vacuum chucks, the contact surface with the magnets and vacuum chucks needs to be smoothed to a certain degree before they can be used safely and normally.


4. Clamp using hole clamping


When using a 5-axis processing machine for simultaneous multi-surface processing or mold processing, in order to prevent the influence of fixtures and tools on processing, it is generally more appropriate to choose the method of using hole clamping. Compared with the method of clamping from above or from the side of the workpiece, the method of clamping with the hole generates less load on the workpiece and can effectively deform the workpiece.


Picture ▲Using holes for direct processing


Picture ▲ Set the pull stud for clamping


2. Pre-clamping


The above mainly refers to the fixtures for workpiece clamping. How to improve operability and use pre-clamping is also crucial. When the workpiece is set vertically on the base, the workpiece will fall downward due to gravity. In this case, it is necessary to operate the clamp while pressing the workpiece with the hand.


Picture ▲Pre-clamping


If the workpiece is heavy or many workpieces are clamped at the same time, the operability will be greatly reduced, and the clamping time will be long. At this time, using this spring-type pre-clamping product can operate the clamp while the workpiece remains stationary, greatly improving operability and reducing workpiece clamping time.


3. Matters needing attention when choosing a clamp


When using multiple types of clamps in the same tool, be sure to use the same tools for clamping and unclamping. For example, in the figure on the left below, when multiple tool wrenches are used for clamping operations, the overall burden on the operator will increase, and the overall clamping time of the workpiece will also become longer. For example, in the right picture below, the tools and wrenches are unified, and the bolt size is also unified, which is convenient for on-site operators.


Picture ▲The operability of workpiece clamping


In addition, when configuring the clamp, it is necessary to consider the operability of workpiece clamping as much as possible. If the workpiece needs to be clamped at an angle during clamping, the operability is very inconvenient, and this situation should be avoided when designing the fixture tooling.


Send Inquiry

whatsapp

skype

E-mail

Inquiry