At present, some domestic enterprises have low production efficiency and economic benefits. Compared with some developed countries, they generally suffer from problems such as large consumption, high costs, and low efficiency. By analyzing the production process and equipment of the servo stamping automation line and comparing it with the traditional manual stamping line, it shows obvious advantages in terms of product quality, production rhythm, energy saving, etc. This stamping method is also the future development direction of stamping automation lines.
With the development and progress of the automobile industry, automobile manufacturers have increasingly urgent needs to improve production efficiency, material utilization and product quality. The application of stamping automation lines in the automobile industry has increased rapidly. In order to improve production efficiency and reduce Cost and quality improvements bring direct economic benefits.
At present, stamping workshops are mostly manual production lines with low production efficiency, high labor intensity and low surface quality of stamping parts, which can no longer meet production needs.
The servo stamping automated production line is composed of a servo press and an automated conveying system. In existing stamping production lines, the matching presses are mainly multi-link mechanical presses. Although automated stamping production has been achieved, the demand for high-quality, high-tempo, and low-cost production has not yet been solved. The birth of the servo stamping automated production line This can solve the above problems and plan the mainstream direction of stamping lines for future automobile factories.
Production process and equipment
Destacking
It is the first process of the stamping automated production line. It consists of a depalletizing trolley and a depalletizing robot. A crane or forklift is used to transfer the sheets to be produced to the depalletizing trolley for positioning. The magnetic spreader on the depalletizing trolley separates the sheets. The materials are separated, and then the sheets are placed on the feeding belt conveyor through a depalletizing robot to realize the sheet destacking process. Figure 1 shows the schematic diagram of the depalletizing robot.
picture
Figure 1 Depalletizing system
Clean
The conveyor equipment belt conveyor transports the sheets captured by the depalletizing robot to the cleaning and oiling equipment. The dust and oil on the surface of the sheets are removed by the cleaning machine to meet the cleanliness requirements required for production. Currently, the mainstream cleaning machine in the main engine factory is German SMT cleaning. machine, as shown in Figure 2.
picture
Figure 2 German SMT cleaning machine
oil
After cleaning, the sheet metal is sprayed with a thin oil film by the oil coating equipment. You can choose single-sided, double-sided or no spraying methods. The area of the sprayed oil film is adjustable. The oil film attached to the surface of the sheet is beneficial to the forming of stamping parts and prevents cracking. , to improve product quality, the current mainstream cleaning machine in the main engine factory is the German SMT oiling machine, as shown in Figure 3.
picture
Figure 3 German SMT oiling machine
centering
Alignment systems are generally divided into two categories: mechanical alignment and visual alignment. Currently, most OEMs use visual alignment. This specifically refers to the visual alignment system. After cleaning and oiling, the sheet metal is transported to the transition belt conveyor directly below the centering system. The position information of the sheet material is transmitted to the loading robot by taking pictures. The robot can smoothly grab the sheet material by adjusting the grabbing position, thus Achieve sheet centering. The alignment system is shown in Figure 4.
picture
Figure 4 Alignment system
Forming
The loading robot grabs the sheet and places it on the first servo press for drawing. It adjusts the servo control system to stop the servo press at any position, increases the holding time, and obtains the first formed part of the required shape. The transfer robot grabs the sheet material and transports the sheet material between the presses; after the post-sequence servo press completes the drawing, trimming, punching, flanging and shaping processes, the required stamping parts are obtained.
The number of servo presses is set according to the number of mold production processes. It is generally considered as 4 or 5 units. The tonnage of the first servo press can be selected as 2500t to complete the drawing process. The tonnage of the subsequent press is generally 1000t to complete edge trimming, Punching, flanging and shaping processes. The servo press is controlled by a servo motor, which directly drives the linkage mechanism to drive the slider to move up and down in a linear motion. Due to the characteristics of the servo motor, the slider can stop at any position, and the workpiece forming holding time is controllable. It is also equipped with a CNC stretching pad. , the blank holder force is adjustable and can produce high-quality stamping parts. The servo press is shown in Figure 5.
picture
Figure 5 Servo press
Loading, unloading and transmission
Compared with the traditional mechanical press automated conveying line, the automation part is basically similar. The loading and unloading mechanisms basically use six-axis robots, which can meet the set maximum production cycle loading and unloading requirements. The sheet metal transfer between presses involves many factors such as the pick-up angle, press stroke, and press automation matching information. It usually uses manipulators or linear seven-axis [3] robot equipment. The content covered in this article mainly refers to seven-axis robots. Basically it can satisfy most countries
In-house OEM production and post-production cycle time improvement needs; for high-speed stamping lines, single-arm or double-arm manipulators are required to achieve the required production cycle time. The six-axis robot is shown in Figure 6, and the seven-axis robot is shown in Figure 7.
picture
Figure 6 Six-axis robot
picture
Figure 7 Seven-axis robot
Unloading, conveying and inspection
The unloading conveyor is generally carried out by two parallel belt conveyors. The unloading robot grabs the finished parts and places them on the belt conveyor. The belt conveyor transports them to the manual packing area. During the transportation process and before packing, the finished parts are manually inspected to ensure they are qualified. The products are directly loaded into the work station equipment, and the unqualified products are transferred to the repair area for repair. The belt conveyor is shown in Figure 8.
Figure 8 Belt conveyor
The sheet metal is transported to the loading trolley by a forklift or crane. The loading trolley starts and transports it to the designated location. The depalletizing robot starts to work, placing the sheet metal on the conveying equipment. The dust and oil on the surface of the sheet material are removed through the cleaning machine, and then Use the oiling equipment to spray a thin layer of oil film. The sheet passes through the visual centering device and takes a photo to transmit the position and size information of the sheet to the loading robot. The entire line control system adjusts the gripping angle of the loading robot to grab the sheet. . The loading robot grabs the sheet and places it on the first 2500t servo press for the drawing process. The servo control system can be adjusted to stop the servo press at any position, increase the holding time, and obtain the first formed part of the required shape. Then, the sheet metal is grabbed by a transfer robot and transported between the presses. After three or four 1000t presses complete the drawing, trimming, punching, flanging and shaping processes, the required stamping is obtained. Finally, the finished stamping parts are placed on the optical inspection belt through the unloading robot and inspected by workers. Qualified products are placed on the work station equipment and transferred to the stamping parts warehouse for storage by forklifts. Unqualified products enter the repair area. After passing the repair Restock.
Servo press features
Digital servo systems have received widespread attention due to their extremely fast response speed, extremely high precision, and flexible and convenient control. In production, the motion curve trajectory of the servo press can be easily adjusted by modifying the position and speed command values of the servo drive in the servo control system through the PLC.
Compared with mechanical presses, the main features are as follows:
①No clutch/brake required;
②No need for flywheel or flywheel brake;
③No drive belt required;
④No need for slider balancer;
⑤Simple structure and convenient maintenance;
⑥The motion curve trajectory is adjustable and the production efficiency is high;
⑦Low energy consumption;
⑧ Stamping parts have high surface quality.
Advantages of servo stamping line
Servo stamping automation lines have huge advantages over traditional manual mechanical lines, which are mainly reflected in the following aspects:
① The servo press can stop at any position, has a long pressure holding time, good formability of stamping parts, and good product quality;
② The servo press has an energy recovery function and the stamping line consumes low energy;
③ There is no manual oiling, manual loading and other processes at the line head;
④ Sheet material transmission does not need to be conveyed through a belt conveyor, and linear transmission is achieved through an upside-down robot;
⑤ The sheets will not come into contact with each other during the transfer process, avoiding collisions on the sheet surfaces;
⑥ Greatly reduce labor intensity, no manual handling is required for loading and unloading materials;
⑦The servo stamping line requires less personnel investment and low labor costs.
Combined with the current development trend of the automobile industry, new materials, high-strength steel, and new processes are constantly being applied, which requires continuous improvement and development of stamping line equipment to adapt to the new needs of the development of the automobile industry. The use of servo stamping lines can solve the above-mentioned new product forming needs and meet the requirements for product quality, production capacity, safety and environmental protection, etc.




