Dec 11, 2023 Leave a message

There Are So Many Ways To Eject The Mold, I Guarantee You Can’t Tell.

 

In order to improve the injection molding efficiency and the quality of molded products, it is also necessary to implement automatic operation. For this reason, it is necessary to be able to automatically and reliably demold the sprue, runner and molded products.

In addition, for products produced in small quantities, the number of days and prices for mold production are limited, and when the shape of the molded product and the type of gate cannot allow automatic demolding, the molded product and sprue can be determined at this time. The runner is the easiest to demold. Mold ejection mechanism﹒

Molded products of the same shape also have different ejection methods due to different material types and gate forms. The most appropriate method must be used in combination.

Ejection of molded products


The decision of the ejection method of the molded product is of course affected by the material and shape of the molded product, but in principle, gaps, levels, etc. are made on the molded product to achieve the most reliable demolding, with fewer failures and no more failures. Where it occurs, it must be easily repairable.

Molded products of the same shape also have different ejection methods due to differences in appearance, accuracy, and formability.

Ejection methods generally use ejection pins (straight pins, staged pins), sleeves, scrapers, air, etc., which can be used alone or in combination, depending on the life span of the mold and the difficulty of mold processing.

(1)Types of ejection


1) Push out the tip

The processing of the tip is the easiest. When the hardness is required, it is easier to perform quenching and grinding than other methods. It can be placed at any position of the molded product, which is the most commonly used method.

The hole is easy to process, the accuracy can also meet the requirements, the sliding resistance is minimal, and the occurrence of locking is less. Because of the long mold life and interchangeability, repairs can be easily made when damaged.

However, when ejecting on a small area, the ejection stress is concentrated on the local part of the molded product. Cups and box-shaped items have small shrinkage and inclination, and the molded products have high demoulding resistance. In this case, depression and ejection will occur. Most of the time, the use of ejection pins is inappropriate.

2) Square or plate-shaped ejection tip

There are no difficulties in the processing and heat treatment of plate-shaped ejector plates and other parts, but the processing of holes is difficult and requires special processing such as electric discharge machining.

By dividing the mold template and the heart-shaped part to form a combined shape, the processing becomes easier, but the manufacturing time is increased. Since the molded product has dividing lines, it has a negative impact on the appearance of the transparent part, and there are also situations where it is not allowed. Furthermore, the sliding resistance is also relatively low, with many round tips and the thickness of the board is relatively thin, which can easily cause bending and buckling. Avoid using it to the extent possible.

3) Sleeve

The processability of the sleeve is relatively good, but the sleeve with a small inner diameter and a long length is more difficult to process, and is prone to cracking when used on thin parts.

Since the end face of the sleeve is fully ejected, the molded product is ejected uniformly, which can ensure reliable demoulding and reduce the occurrence of cracking of the molded product.

4) Scraper

The processing of the scraper plate and the heart shape is not more difficult than the ejection pin. The mechanical processing and matching of the sliding surface requires more time. The fitting part of the sliding surface must be quenched, and heat treatment is more difficult. Furthermore, interchangeability tends to be poor, and repairs require more labor.

If the shape of the scraper plate and the heart-shaped mating surface is round or square, machining and mating processing are relatively easy, but if it is a continuously changing curve, it becomes difficult.

Furthermore, in order to maintain interchangeability after quenching, bushings are used to embed, making repairs easy. Especially if there are several holes, only the damaged single piece can be replaced.

Compared with other ejection methods, the scraper plate has a large ejection area, and the molded products can be reliably demoulded. It is effective in demoulding molded products such as cups and hats that have greater demoulding resistance, and is widely used. Furthermore, there are almost no signs of ejection on the appearance, which is also one of the advantages.

5) Air pressing method

The air extrusion method is to set up a valve, etc., to pass air into the gap. The processing is relatively simple, and it is an extremely effective method for demoulding molded products with large depths such as cups and boxes.

(2) Example of ejector mechanism


picture

Figure 1 shows the case where only the ejection pin is used﹒ The position of the ejection pins should be arranged at a place with greater demoulding resistance. If the demoulding resistance is uniform, it should be arranged evenly. The cups and boxes shown in the figure form a molded product, and the side resistance is the greatest. In the best case, the ejection pin is arranged here. Furthermore, if the ejection pin is arranged on the inner side, it is better to arrange it near the side wall. central part, otherwise it will easily cause cracking when ejecting.

picture

Figure 2 shows the situation where there are thin and deep bosses and reinforcing ribs. If the ejection pin is used to eject around them, cracking will occur, which will easily cause the molded product to be damaged and scrapped. The ejection pin must be set at the bottom of the boss and the reinforcing ribs. Enables reliable demoulding﹒

picture

Figure 3 is an example of using a layered ejection pin. Since it is impossible to use a small ejection pin for small molded products, the deflection is reduced because the middle section is thicker.

picture

Figure 4 is an example of using the ejection pin and the scraper together. The inner surface of the heart-shaped mold has a greater resistance to demoulding. If only the scraper is used to demould, there may be broken residues. To prevent this kind of defect from happening, set The ejection tip becomes the main scraper, and the ejection tip is used as a supplement. In this case, the ejection pin is set inside the heart, causing a heart-shaped cooling failure. Using a small diameter heart can be used for direct cooling, which can eliminate this shortcoming. The shape of the molded product must be considered to make it possible to install an ejection pin. Sexually eliminated, and can be removed from the mold.

picture

Figure 5 shows some parts with strong demoulding resistance (less and deeper shrinkage). For example, in the case of tubular protrusions, when the ejection pin is used to eject the peripheral and inner surfaces, the molded product will also crack. Leather cover When the cylinder is ejected, the ejection tip is the main one, and the sleeve is the auxiliary mechanism.

picture

Figure 6 and Figure 4﹒ Figure 5 takes the same consideration and shows an example of using a scraper plate and a sleeve together.

picture

Figure 7 shows the situation where the inner and outer peripheral tools are embedded in the movable side of a deep tubular molded product. It is most effective to use a sleeve to push out the end face of the molded product.

picture

Figure 8 shows an example where long sleeves are difficult to process but short sleeves are easy to process.

picture

In general, when ejecting basin-shaped products, the scraper plate shown in Figure 9 is mostly used. If the inclined basin end ejection pin shown in Figure 10 is used, the processing is simple. And use a scraper plate to cool the heart, as shown in Figure 4 and Figure 5. There are shortcomings﹒

picture

picture

Figure 11﹒ Figure 12 shows the situation of using air to press out﹒ When using a scraper to eject large, deep, and thin shaped products (boxes, cups, etc.), the molded product may buckle. Furthermore, a vacuum may be formed between the molded product and the heart shape, causing the molded product to break. When used in soft materials such as polyethylene, the degree of breakage is more significant. In this case, air pressure is the most effective. Figure 11 shows the method of using only air. Figure 12 shows an example of using a scraper with air pressure between the heart shapes. ﹒

How to take out threaded molded products


If the molded product has threads, there are three demoulding methods:

1) Die thread part die

2) Place the insert into the threaded part of the mold﹒

3) The molded product rotates on the threaded part of the mold﹒

(1)Mold thread part mold


This method is suitable for external threads (the mold structure of male threads is relatively simple to manufacture and can be reliably demoulded).

However, the threaded part of the molded product has a waste edge that squeezes into the parting line. The molded product is processed later, and the cooperation with the fitting part causes a failure.

(2) Insert the insert into the threaded part of the mold


If the mold structure cannot use mold splitting and rotation, the inserting fitting method can be used when the mold structure is simple.

However, when using this method, after the molded product is ejected, the insert must be removed. When the molded product is externally threaded, it is easy to remove due to shrinkage. However, if it is internally threaded, the inserted component must be removed from the molded product. The contact angle area is large and it is difficult to take out. Due to the material of the molded product and the large contact area, it is difficult to take out.

(3) When the molded product rotates at the threaded part of the mold


Generally, covers, etc. are molded products with internal threads, and most of them are automatically rotated out.

In this case, either one of the molded product and the mold rotates and makes a withdrawal movement, or one piece only rotates and the other part withdraws, but the molded product must have sliding positioning (rotation stop).

When the outer circumference of the molded product is slidably positioned and the mold with dotted gates is opened and the rotation starts at the same time, the molded product and the threaded part of the mold are demoulded. Due to the pressure of the parting surface, the demoulding resistance of the parting surface is large and the molding process is completed. The thread of the thread is broken﹒

In order to prevent this defect, the speed of thread withdrawal must be designed to be the same as the speed of the mold opening mechanism of the parting line. Furthermore, when there is a place with strong demoulding resistance outside the threaded part of the molded product, the ejection function must be at the same speed at the same time as the rotation is started.

Although the rotary damage can be set on both the fixed side and the movable side of the mold, the molding machine is generally set on the opposite side of the nozzle and ejection mechanism. Due to the configuration of the sprue, the runner and the ejection relationship, the rotary mechanism is set on the opposite side of the nozzle and ejection mechanism. The movable side is advantageous in terms of mold structure and forming efficiency.

1) When there is sliding positioning on the outer circumference of the molded product

Image] [image

Figure 13 shows the outer point gate, and Figure 14 shows the inner point gate. Both use special ejection pins, scrapers, etc. to eject them. After the thread (a) is rotated several times between the mold openings, If the center of the molded hole or the top of the heart breaks away, the molded product will naturally fall.

picture

Figure 15 shows the case where the molded product is slidingly positioned and the mold core is on the movable side. After the rotation is completed, the molded product is ejected from segments H and h, and then falls out of the mold.

As shown in the figure, when H>h, the ejection mechanism of the ejection pin (b) must be installed. As shown in Figures 13 to 15, it is suitable for the gate to be automatically cut off during demoulding. In the case of lateral gate, the runner and the molded product move at the same time, and an ejection mechanism with the same speed must be installed.

2) When there is sliding positioning on the inner surface of the molded product

picture

Figure 16 shows that there is a sliding positioning on the inner flat surface. (a) It rotates and moves at the same time. After the thread mold is removed, the sliding positioning is still attached. It is necessary to install a separate removal device so that the formed part can fall on its own.

picture

Figure 17 shows the case where there is a sliding positioning external thread on the inner surface. (a) Rotate and unscrew the thread according to the pitch of the thread of the molded product. Then you must use the ejection pin (b) to eject it.

Image] [image

Figure 18, Figure 19 There is a sliding positioning on the inner side, only (a) rotation and (b) fixed. After the thread is unscrewed and demoulded, it is ejected through the scraper. The role of the scraper is to use the ejection pin. , springs and other various methods.

3) Where the end face of the molded product has sliding positioning

Image] [image

The end faces of the molded products shown in Figure 20 and Figure 21 are all slidingly positioned. In order to allow them to fall naturally, an additional ejection device (a) must be installed. For small molded products with side gates, the molded products cannot be moved For direct ejection, it needs to be ejected together with the runner. Furthermore, there is no need to set up a special sliding positioning. The gate can be used as the sliding positioning set on the end face. However, for soft materials, if there is no fairly large gate, there will be shearing possible.

4) Pinion connection method that rotates and reciprocates at the same time

picture

Figure 22 shows a heart-shaped wheel that rotates and reciprocates while being directly connected to the pinion. Figure 23 shows a heart-shaped wheel that is indirectly connected to the pinion. The sliding resistance of the reciprocating motion in Figure 23 is smaller, and can function smoothly, with a larger reciprocating stroke. In Figure 22, the strength is relatively good. In the case where the mass has a heart-shaped tip, there is no difference from the one used in Figure 22.

5) Driving method of thread heart shape

Image] [image

picture

picture

Figures 24 and 25 use the mold opening stroke.

Figure 26 and Figure 27 are equipped with separate power sources such as hydraulic and electric motors. The advantage is that the timing of starting and stopping the rotation can be freely controlled, but a power control device is required. When the molded product bolts rotate a lot, Figure The driving method shown in 27 is the best one.

The main point gate is injected into the channel and the ejection of the first channel is

When the lateral gate has a runner and a gate in the molding surface, the molded product can fall off at the same time, and it is easy to fall off naturally. However, in cases such as point gates, it is difficult to fall off naturally.

picture

When there is no runner stripping mechanism as shown in Figure 28, manual demolding is necessary. The mold structure is the simplest, but the forming efficiency is low, and it should not be used except for small-scale production.

picture

picture

Figure 29 shows a runner scraper, but in the stripped state, the sprue is suspended in the hole of the runner scraper and cannot fall off naturally. In this case, an ejection point should be set in part A, and air pressure should be used if necessary. Press it off.

Image] [image

Figure 30 shows a simpler structure. The number of completed processing steps is less. The flow channel length L is larger than l. If l is deeper than the above situation, when the flow channel floats, it will be embedded in the side of the mold template and cannot fall off naturally. .Furthermore, if the cooling time is long, part of the runner is bent, and the gate part that once floated will still spring back to the side of the mold.

Furthermore, there are vertical ridges on the side of Part A, which are attached and do not fall off. In addition, if the molded product is placed directly below the sprue, the sprue positioning cannot be installed, making it difficult to use. However, there is no need to use springs and extensions. Install other devices, and at the same time as the mold is opened, the gate can cut off the points of interest.

picture

The advantages and disadvantages of Figure 31 are roughly the same. Part A in Figure 30 is not attached, and part of the flow channel is embedded in the side of the mold template, so that it can float and fall off.

However, the sprue ejector is slightly longer than the movable side mounting plate, so it cannot be used on a molding machine without a central ejector rod hole or a molding machine with a central ejector hole that is not deep enough. Picture

Figure 32 is for slender molded products such as pen covers. An ejection plate is installed in the fixed side template, and the flow channel is ejected through the ejection pin. This is only used for limited molded product shapes.

Two sections push out


(1)Use


When a scraper is used for ejection, the flange portion of the molded product is pushed out from the inside of the scraper. This part is still adhered to the scraper. There must be any method to remove it from the molded product. In this case, In order to achieve automatic demoulding, a two-stage ejection mechanism is required.

Figure 33 shows the scraper and ejection pin method. Figure 34 is an example of using two sets of ejection plates to eject a dented molded product in two stages to form a forced ejection.

picture

picture

In the case of two-stage ejection, the two groups of ejection strokes must be different, and the larger side of the stroke will act at the same time or later.

The ejection mechanism of the forming machine is a pressure cylinder and its accessories, as well as a positioning rod and its accessories. In the case of the former, one side consists of the fixed side, which uses screws, bars and rings, etc., to extend according to the mold opening stroke, and the other side consists of the forming machine The ejection mechanism can form two stages of ejection.

But in the latter case, the two groups must be ejected in two stages from the same direction, and the two groups of ejection mechanisms must have ejection stroke timing and stroke adjustment mechanisms.

(2) Two-stage ejection positioning and stroke adjustment mechanism


1) Spring method

picture

Figure 35 shows a mechanism in which the ejection side is driven by a spring. It is easy to manufacture and has a small installation space. It is the simplest mechanism.

But it cannot withstand excessive force, and its effect is unreliable.

2) Pressure cylinder method

picture

Figure 36 shows the use of a pressure cylinder instead of a spring. It works reliably and the timing can be adjusted freely. However, the installation location is large and cannot be used when the forming machine and mold are small. Furthermore, the hydraulic pump and air compressor must be installed.

Special control facilities are required.

3) Cam method

picture

Figure 37 shows the use of a cam instead of a spring and a pressure cylinder. It works reliably and does not require other ancillary facilities.

However, the cam lifter protruding from the fixed side must be installed in a place that does not hinder the removal of the molded product.

4) Jaw clamping method

picture

Figure 38 shows (a) and (b) two sets of ejection plates. The (a) set is ejected directly from (c). The (a) set is connected to (a) by the clamping jaw (d). During the action stroke, (a) d) Perform two-stage ejection.

5) Set up the ejection plate of the sliding part

picture

Figure 39 shows the scraper plate and the ejection pin acting at the same time. There is a sliding member directly below (a). Due to the movement of the sliding member, the scraper plate stops functioning during the action of the ejection plate, and two stages of ejection are performed.

Furthermore, the contact surfaces of (a) and (b) must be smooth.

Ejection plate advance return mechanism

For molds using split molds and lateral heart-shaped molds, if the ejection pin is installed, when opening the mold, the ejection pin must be retracted before the sliding part is retracted.

Otherwise, the two will conflict and be damaged.

1) Spring method

Figure 40 shows an advanced retraction mechanism using a spring as the ejection plate. In this case, the mold structure and processing are the simplest, and the installation location is also small.

picture

However, the ejection pin sometimes seizes, which makes the advance retraction effect unreliable, the sliding part conflicts with the ejection pin, and the mold is damaged. Furthermore, if the ejection stroke is large, the spring compression ratio becomes larger, so use a spring of considerable strength. , the ejector plate does not retreat in advance during the action process, and the action is avoided as much as possible.

2) Link method

picture

Figure 41 shows the use process. It works reliably and will not cause malfunction. However, the action rod (a) protruding from the fixed side is long and must be installed in a place where there is no obstruction when taking out the molded product.

3) Joystick method

picture

Figure 42 shows the use of a joystick. Its advantages and disadvantages are the same as those in the use phase. However, when the ejection plate is fully restored and must be released, more attention must be paid to the timing adjustment.

4) Gear method

picture

When the gear is used as shown in Figure 43, the function is real and the same as the link method. The considerations regarding the removal of the molded product must be the same as the link method and the joystick method. The difference from other methods is the function of the ejector plate, reciprocating motion, etc. Implemented by a rack, the stability of the ejection function of the ejection plate must be considered.

5)Hydraulic cylinder method

The advantages and disadvantages of this method of mechanism are: in the case of two-stage ejection, the effect is reliable and the timing can be adjusted freely; the disadvantage is that the device is complicated.

Send Inquiry

whatsapp

skype

E-mail

Inquiry