Oct 30, 2021 Leave a message

What Causes The Poor Accuracy Of Vmc850 Cnc


The processing accuracy of vmc850 cnc is out of tolerance mainly due to the high surface roughness value of the inner hole processing, the reaming inner hole is not round, the reaming position accuracy is out of tolerance, the inner surface of the hole is obviously edged, and the straight center line of the hole after reaming is outside. The increase or decrease of the pore size, etc.


1. The position accuracy of the reaming hole is out of tolerance


 Causes: It may be caused by wear of the guide sleeve of the vertical machining center, the distance between the bottom end of the guide sleeve and the workpiece is too large, the length of the guide sleeve is too short, the accuracy is poor, and the spindle is loosened.


Solution: When reaming a vertical machining center, if the position accuracy of the hole is out of tolerance, the following maintenance can be carried out according to the above problems, and the extended guide sleeve should be replaced regularly. The clearance fit accuracy can improve the gap between the guide sleeve and the reamer. Overhaul the machine tool and adjust the spindle bearing clearance.


 2, the surface roughness of the inner hole is high


   Reasons: The surface roughness of the inner hole processed by the CNC 850 machining center is relatively high, which may be caused by multiple reasons such as excessive cutting speed, improper cutting fluid selection, excessive or excessive reamer entering angle. The reaming allowance, the reaming allowance is uneven or too small, the cutting edge is not sharp, the reaming edge is too wide, the chip removal during reaming is poor, the reamer wear is too large, or the selected milling cutter and the part material are different. match.


  Solution: There are many reasons for high processing roughness, so the solution is more complicated. We can start from the following aspects: reduce the cutting speed, select the cutting fluid according to the processing material, appropriately reduce the reaming allowance, improve the accuracy and quality of the bottom hole before reaming, or increase the reaming allowance to increase the reaming allowance quantity. Leave space for chip flutes or use reamer with inclined cutting edge to make chip evacuation smooth. Replace the reamer regularly and choose the cutter reasonably.


  3, the processing hole diameter increases


   Reasons: The diameter of the hole gradually increases during processing on the CNC 850 machining center. The reason may be: the design value of the outer diameter of the reamer is too large, or the reamer edge has burrs, the cutting speed is too high, the feed rate is improper or the machining allowance is too large, the entering angle reamer is too large, the reamer is bent, and the reamer edge is too large. There are built-up tumors in the mouth, the swing of the reamer edge is out of tolerance during grinding, and the improper selection of cutting fluid may also be a problem of the CNC machine tool itself. The above problems can also occur if the spindle is bent or the spindle bearing is too loose or damaged.


Solution: According to the actual inspection, the following countermeasures can be taken: appropriately reduce the outer diameter of the reamer, reduce the cutting speed, appropriately adjust the feed rate or reduce the machining allowance, appropriately reduce the entering angle, straightening or scrap bending can not use the reamer , Choose a cutting fluid with good cold performance, adjust or replace the spindle bearing, or replace the entire spindle.


  4, the inner hole of the reaming hole is not round


Causes: The processed inner hole is not round and the roundness is not enough, mainly caused by the following factors: the reamer is too long, the rigidity is insufficient, the vibration occurs during reaming, the main deflection angle of the reamer is too small, the reaming allowance is too small, and the inner Intersections and gaps on the surface of the hole, especially sand holes and pores on the surface of the hole, may loosen the spindle bearing of the machine tool.


Solution: The following aspects can be taken: the installation of the reamer should be rigidly connected, the qualified reamer should be selected, the hole position tolerance of the pre-processing process should be controlled, the unequal pitch reamer should be used, the qualified blank should be selected, and the spindle should be adjusted in time gap.


  5, the center line of the reaming hole is not straight


   Cause: When machining holes on the CNC 850 machining center, the center line is not straight. The possible reason may be: the hole is inclined when drilling, especially when the hole diameter is small. Due to the poor rigidity of the reamer, the original curvature cannot be corrected, the main deflection angle of the reamer is too large, and the guidance is poor, which makes the reamer easy to deviate from the direction when reaming.




Send Inquiry

whatsapp

skype

E-mail

Inquiry