Feb 02, 2024 Leave a message

Stamping process and stamping die terminology

 

Stamping process is a metal forming process, and together with welding, painting, and final assembly, it is known as one of the four major processes of automobile manufacturing. Therefore, without stamping, cars may still be made by knocking and knocking, and three cars a month can be produced. Oh~ Today we are going to learn the definitions of 72 technical concepts of stamping with you, so that you can use them in future work.


Stamping process professional terms

1. Work piece

The workpiece is a punched piece that has completed each process specified in the process document.

2. Process parts

Process parts are blanks or punched parts that have been stamped, but need to be further stamped.

3. Last item

The upper part is to feed the process part into the mold for further stamping.

4. Loading device

The loading device is a device that feeds the process parts into the mold.

5. Top dead center

The top dead center is the upper end point of the press slider moving up and down.

6. Bottom dead center

The bottom dead center is the lower end point of the press slider moving up and down.

7. Burr

Burrs are sharp protrusions on the edges of the punched parts after punching.

8. Burr surface

The burr surface is the flat surface of the blanking part with burrs on the edge. For blanking, the burr surface is the plane that contacts the punch; for punching, the burr surface is the plane that contacts the die.

9. Rough surface

The rough side is the torn and rough section of the blanking part.

10. Neutral layer

The neutral layer refers to the layer of material in the bent stamping where the strain is zero.

11. Neutral layer coefficient

The neutral layer coefficient is a system used to determine the location of the neutral layer.

12. Double-sided gap

Double-sided clearance is the clearance from one side to the opposite side or the sum of the clearances on both sides.

13. Delivery

Part removal is to remove the punched work (process) parts from the mold.

14. Output device

The ejection device is a device that allows the punched work (process) parts to be ejected from the mold.

15. Positive rebound

Positive springback is the springback in which the curvature radius increases after the formed stamping part is taken out of the mold, or the rebound in which the material entity increases after the blanking part escapes from the mold.

16. Stamping parts

Stamping parts are the collective name for blanks that have gone through one or more stamping processes, which is also the collective name for process parts and workpieces.

17. Glossy

The smooth surface is the bright section cut out of the blanking part.

18. Closing height

The closing height is the distance between the upper plane of the upper mold base or the plane of the lower mold base when the punch is at the lower extreme of the working position.

19. Rebound

There are two types of springback. One is the difference between the size of the formed stamping part after it is taken out of the mold and the corresponding size of the mold. For bent parts, it is generally expressed as angle difference or radius difference. The other is the difference between the outer dimensions of the blanking parts that escape from the mold and the corresponding dimensions of the die, or the difference between the inner dimensions and the corresponding dimensions of the punch.

20. Itinerary

The stroke is the distance between the end points of the up and down movement of the press slider. It is customary to refer to the up and down movement of the press slider as a stroke, such as "stroke down", "stroke up", "strokes per minute", etc.

21. Negative rebound

Negative springback is the springback in which the radius of curvature of a formed punched part decreases after it is taken out of the mold, or the rebound in which the material entity shrinks after the punched part escapes from the mold.

22. Clamping and feeding device

The clamping feeding device is a device that uses the clamping, loosening and reciprocating actions of a mechanical, pneumatic or hydraulic press to feed raw materials into the die.

23. Lifespan

Life span refers to the number of times the die can be punched each time it is repaired or the number of times the die can be punched before it is scrapped. The former is called sharpening life, and the latter is called total life.

24. Step distance

The stepover is the distance that the raw material can be fed each time for multiple stampings.

25. Gap

The gap is the difference in the corresponding dimensions of the matching punch and die or the gap between them.

26. Single-sided gap

A one-sided gap is a gap from the center to one side or a gap on one side.

27. Blank

The blank is not stamped, and most of the raw materials are only used for one stamping. The blank is sometimes called blank or rough stock.

28. Coil material

Coil stock is a roll of raw material that can be used for multiple punches.

29. Sheet material

Sheet stock is a plate-shaped raw material that can be used for multiple stampings.

30. Strips

Strips are strips of raw material that can be used for multiple punches.

31. Pull marks

Pull marks are the friction marks between the material surface and the working surface of the mold during the forming process of the punched parts.

32. Drawing ratio

The drawing ratio is the reciprocal of the drawing coefficient.

33. Drawing coefficient

The drawing coefficient is the ratio of the diameter of the cylindrical drawing part in this process to the diameter of the drawing part in the previous process. For the first drawing pass, the drawing coefficient is the ratio of the diameter of the drawn part to the developed diameter.

34. Tug

Lugs are ear-shaped protrusions on the upper edge of the drawn piece.

35. Feeding

Feeding is the feeding of raw materials into the mold for stamping.

36. Feeding device

The feeding device is a device that feeds raw materials into the mold. Common feeding devices include roller type, clamping type, hook type, etc.

37. Hopper

The hopper is a bucket-shaped container with an automatic directional delivery mechanism for formed stamping parts.

38. Bending radius

The bending radius is the inner radius of the bend of the punched part.

39. Expanded view

The expanded view is a flat process part graphic corresponding to the formed stamping part.

40. Expanded size

The expanded size is the size of the flat process piece corresponding to the size of the formed stamping piece.

41. Arching

Arching is the name of the phenomenon of uneven arching on the surface of stamping parts.

42. Wrinkling

Wrinkling is the name of the phenomenon where the flange of a deep-drawn part produces wavy wrinkles.

43. Feed trough

The trough is a groove-shaped channel that allows punched parts to enter or leave the mold sequentially.

44. Hook feeding device

The hook feeding device is a device that uses a reciprocating hook to extend into the hole to drive the raw materials into the die.

45. Document handling

Part sorting is to arrange and stack the punched parts (mostly blanked parts).

46. Piece management device

The piece sorting device is a device that sorts and stacks stamped parts.

47. Layout

Layout is the die design process that completes the layout drawing. Sometimes the layout diagram is also referred to as layout.

48. Layout drawing

The layout diagram is a layout diagram that describes the gradual formation process of punched parts on the strip (strip, roll) material, the final position occupied and the relationship between adjacent punched parts.

49. Mold sticking

Mold sticking is the name of the phenomenon where the working surface of the die is bonded to the punching material.

50. Broken blade

Edge chipping is the name of the phenomenon where small pieces of the cutting edge of the punch or die peel off.

51. Minimum bending radius

Minimum bend radius refers to the smallest bend radius that can be successfully bent.

52. Take the edge

Overlap is the minimum distance between adjacent punched parts outlines in the layout diagram, or the minimum distance between the punched part outlines and the edge of the strip.

53. Collapse angle

The sagging angle has two meanings. One refers to the phenomenon that the outer edge of the blanking part is rounded near the concave die surface or the inner edge is close to the punch surface. The other refers to the height hg of the part where the cross section of the blanking part has a sagging angle.

54. Slumped angle surface

The sag surface is the plane of the blanking part with a sag edge, that is, the opposite side of the burr surface.

55. Trial mold

Trial mold refers to the experimental stamping performed after the mold assembly is completed to assess the mold performance and stamping quality.

56. Roller feeding device

The roller feeding device is a device that uses pairs of rollers to clamp the raw materials and feed them into the die. Material feeding is accomplished by periodic rotation of the rollers.

Stamping die terminology

picture

1. Blanking

Blanking is a stamping process that uses a die to separate part of the material or process piece from another part of the material, process piece or scrap. Blanking is a general term for separation processes such as cutting, blanking, punching, punching, grooving, sectioning, chiseling, trimming, tongue cutting, cutting, and trimming.

2. Cut

Cutting is a stamping process that separates material partially, but not completely, along an open contour. The material that is cut and separated is located at or substantially in the plane in which it was before separation.

3. Trim edges

Trimming is a stamping process that uses a die to trim the edges of the forming process parts so that they have a certain diameter, height or shape.

4. Tongue cutting

Tonguing is a stamping process that separates material partially, but not completely, along an open contour. The partially separated material has a certain position required by the workpiece and is no longer located on the plane before separation. cut off

5. Cut off

Cutting is a stamping process that separates materials along an open contour. The separated materials become workpieces or process parts.

6. Expansion

Flaring is a stamping process that expands the open part of a hollow or tubular part outward.
7. Punching

Punching is a stamping process that separates waste materials from materials or process parts along a closed contour to obtain the required holes in the material or process parts.

8. Shortage

Punching is a stamping process in which scrap is separated from a material or process piece along an open contour that forms a notch whose depth does not exceed its width.

9. Grooving

Notching is a stamping process in which scrap is separated from a material or process piece along an open contour that is groove-shaped and whose depth exceeds its width.

picture
10. Punch center hole

Center hole punching is a stamping process that forms a shallow concave center hole on the surface of the workpiece. There is no corresponding protrusion in the back material.

11. Fineblanking

Fine blanking is a type of smooth blanking. It uses a fine blanking die with a toothed press plate to make the entire section of the punched part completely or basically completely smooth.

12. Continuous mode

A continuous die is a die with two or more stations. The material is fed into one station successively along the press stroke, so that the punched parts are gradually formed.

13. Single process mold

A single-process die is a die that only completes one process in one stroke of the press.

14. Combination die

The combined punching die is a universal, adjustable complete set of punching dies that gradually forms various punching parts based on geometric elements (straight lines, angles, arcs, holes) one by one. The outline of flat stamping parts generally requires several sets of combined punching dies to be stamped in batches.

15. embossing

Embossing is a stamping process that uses a punch to squeeze into one side of the workpiece, forcing the material to flow into the opposite pit to form a bulge.

16. Embossed

Embossing is a stamping process that forcibly partially displaces materials to form shallow concave patterns, patterns, text or symbols on the surface of the workpiece. The back side of the embossed surface has no ridges corresponding to the dimples.

 

 

Send Inquiry

whatsapp

skype

E-mail

Inquiry