Several parameters to pay attention to when choosing types of end mills
In our work, we often buy tools like this, "Buy milling cutters with the specifications and hardness is the end." The purchasing information of the type of end mills is not only this, it is because of a lot of sales. The personnel do not know enough about the tool professionally. In addition, the technical personnel lack the theoretical knowledge of the tool and do not know what kind of tool is processed and what kind of material. Instead, this procurement model has become the mainstream. In order to meet the needs of different customers, many tool manufacturers mainly sell general-purpose tools. However, this choice does not bring good economic efficiency to parts processors. Today I will share with you the most important geometric parameters of a type of end mills.
First, let's take a look at the components of the types of end mills, as follows:
We need to know the parameters of purchasing a set of end mills
(1) Blade diameter of types of end mills
(2) Blade length of types of end mills
(3) Shank diameter of types of end mills
(4) Full length of types of end mills
(5) Number of teeth of types of end mills
The geometric angles that need to be known when choosing the type of end mills are as follows:
(1) Rake angle (there are positive and negative rake angles,)
(2) Back corner,
effect:
Mainly to reduce the friction between the flank face and the workpiece;
Scope of application:
Rough machining types of end mills, or when machining high-strength and hard workpieces. A smaller relief angle should be selected to ensure that the cutter teeth have sufficient strength; when processing a workpiece with large plasticity or greater elasticity, the relief angle should be increased to avoid the elastic recovery of the machined surface, so that the flank face and the workpiece The friction contact surface is too large.
(3) Helix angle (it is actually the inclination angle of the cylindrical milling cutter or end milling cutter, as shown in the figure below)
Features of helix angle:
The smaller the helix angle, the larger the cutting torque and the smaller the axial tension;
The greater the helix angle, the greater the cutting torque and the greater the axial tension;
Comparison of 30 degree and 45 degree helix angle:
The 30 degree chip removal performance is better and the rigidity is better; but the rake angle is larger and the cutting edge is not sharp enough. Its resistance is large, suitable for low speed and large feed;
The front angle of 45 degrees is sharp; the chip removal performance is not as good as that of 30 degrees, and the rigidity is poor; but under the same number of edges, its chip holding space is large. The front corner is also sharper; suitable for high speed and low feed;
45 degrees is suitable for cutting relatively sticky metals such as high-temperature alloys and stainless steel, and 30 degrees is more suitable for cutting steel, cast iron and other metals;
Most of the end mills on the market are 30 degrees, 35 degrees, 40 degrees, and helix angles;
(4) Number of blades
The more the number of blades, the poor chip evacuation, but the stronger the tool rigidity, the better the surface roughness of the machined surface;
The fewer the number of blades, the smoother the chip removal, but the lower the tool rigidity, the worse the surface roughness of the machined surface;
Applications:
Two blades: suitable for processing keyways;
Three blades: suitable for processing aluminum, plastic, bakelite;
Four-blade: Can be used universally, mainly for processing steel parts. For factories that often process different materials, it is ideal to use four-blade milling cutters to reduce tool costs; for factories with a single material, choose a more appropriate number of blades. Conducive to improving the cutting effect and processing quality.
Types of end mills When grinding, the geometric angles that need to be mastered:
(1) The rear corner of the first end face,
Function: Prevent friction between the end face and the bottom surface of the workpiece, and improve the sharpness of the end face.
(2) Rear corner of the second end face
Function: Conducive to the removal of debris.
(3) Concave angle of the end face,
Function: Prevent the end face of the milling cutter from colliding with the bottom surface of the workpiece, and it is conducive to chip removal.
(4) Axial wedge angle,





